TM-2P

TAPER

AXIS

RPM

TOOL CAPACITY

Toolroom Mill with Tool Changer; 1016 x 406 x 406 mm, 40 taper, 7.5 hp vector drive, 6000 rpm, full enclosure, 10-station automatic tool changer, Visual Programming System, power-failure detection module, 1 GB program memory, memory lock keyswitch, 15″ colour LCD monitor and USB port, Ethernet interface and 76 litre flood coolant system.

TM-2P - Compare to

TM-2P
TRAVELS	S.A.E.	METRIC
X Axis	40 "	1016 mm
Y Axis	16 "	406 mm
Z Axis	16 "	406 mm
Spindle Nose to Table (~ max)	20 "	508 mm
Spindle Nose to Table (~ min)	4 "	102 mm
TABLE	S.A.E.	METRIC
Length	57.75 "	1466 mm
Width	10.5 "	267 mm
T-Slot Width	5/8 "	16 mm
T-Slot Center Distance	4.00 "	101.6 mm
Number of Std T-Slots	3	3
Max Weight on Table (evenly distributed)	1000 lb	454 kg evenly distributed
SPINDLE	S.A.E.	METRIC
Max Rating	7.5 hp	5.6 kW
Max Speed	6000 rpm	6000 rpm
Max Torque	33 ft-lb @ 1200 rpm	45 Nm @1200 rpm
Drive System	Direct Speed Belt Drive	Direct Speed Belt Drive
Taper	BT or CT 40	BT or CT 40
Bearing Lubrication	Grease packed	Grease packed
Cooling	Air Cooled	Air Cooled
FEEDRATES	S.A.E.	METRIC
Rapids on X	400 in/min	10.2 m/min
Rapids on Y	400 in/min	10.2 m/min
Rapids on Z	400 in/min	10.2 m/min
Max Cutting	400 in/min	10.2 m/min
AXIS MOTORS	S.A.E.	METRIC
Max Thrust X	2000 lb	8896 N
Max Thrust Y	2000 lb	8896 N
Max Thrust Z	2000 lb	8896 N
TOOL CHANGER	S.A.E.	METRIC
Type	Carousel	Carousel
Capacity	10	10
Max Tool Diameter (full)	3.5 "	89 mm
Max Tool Weight	12 lb	5.4 kg
Tool-to-Tool (avg)	5.7 sec	5.7 sec
Chip-to-Chip (avg)	6.5 sec	6.5 sec
GENERALS	S.A.E.	METRIC
Air Required	4 scfm, 100 psi	113 L/min, 6.9 bar

Dimensions

N/A

Shipping Dimensions

Brochure

Manual

Rotary Table Fit Chart

See our verticals in action

Haas VF-2SS & HRC210 Demo

This demo was designed to show off the higher spindle speed and rapids of the VF-2SS and the quickness of the HRC210. When combined with strong workholding and modern milling methods, the results are very impressive. The VF-2SS is one of Haas’ most popular vertical machining centres. This is the video debut of the HRC210 roller cam rotary, and it is shaping up to be a great complement to the Haas product line. You can also see in-process probing for part location and feature inspection using the Haas WIPS system.

VF-4 and TR200Y - Cutting Demo

Watch as our VF-4 mill joins forces with our TR200Y 5-Axis trunnion rotary table to put features on 5 sides of this block.

Check out our VF-4 mill here: haas.co.uk/machines/vf-4/

And check out the TR200Y rotary table here: haas.co.uk/rotaries/tr200y/

How We Build VMCs Today

Back in the late 1980s we started building our first VMC, the VF-1. We didn’t build them as efficiently as we do today, but they were good machines and laid the foundation for decades of milling machine development and improvement to come.

Today, our process is finely tuned and quite efficient for a machine that is still hand built to a great extent. Take a look at how we build the same VF that may be sitting on your shop floor not too long from now.

Display Pictures and Videos on Your Haas Control Using M130

Mark shows off the powerful new Haas M130 Media Display feature. By commanding an M130, you can display setup sheets, tool lists, work instructions, and even videos – all within your program. No more taping work instructions to the machine, or hand writing notes telling your operator how to load or inspect a part; put it all in your NC program!